⏱ 9 min read  ·  ✅ Updated Nov 2026

The nozzle is the smallest wear part on an FDM 3D printer, and it is the part that most directly sets line width, detail, and flow. Brass wears wider with every spool, bores clog at the worst moment, and one wrong swap can cost a print. A kit of spares in several sizes and materials covers everyday PLA work, fine detail, fast drafts, and abrasive filament — as long as every nozzle fits your hotend. That fit is the first thing to check: MK8, V6, and Volcano nozzles share an M6 thread but differ in length and melt zone, and they are not interchangeable. The five kits below cover MK8 and V6 hotends, brass and hardened steel, and single-size and multi-size sets.

Our top pick: AXEYIL 50-Piece Mixed-Material MK8 Nozzle Kit. Runner-up: Comgrow 25PCS MK8 Brass Nozzles 0.4mm.

As an Amazon Associate, we earn from qualifying purchases.

How to Choose 3D Printer Nozzles

Fit first: MK8, V6, and Volcano are not interchangeable. All three families use an M6 thread, which invites the assumption that any nozzle fits any hotend. MK8 nozzles are short with a short melt zone and fit Creality Ender and CR-10 style hotends. V6 nozzles are longer with a longer melt zone and fit E3D V6 style hotends such as the Prusa i3 MK3S. Volcano nozzles are longer still, built for high-flow printing. A nozzle with the wrong length seats wrong, leaks filament around the heat break, or leaves a gap that clogs. Confirm which hotend your printer uses and buy only nozzles made for it. Four of the five kits below are MK8; one is V6 only.

Material: brass, hardened steel, or stainless steel. Brass is the standard: it conducts heat well, machines to a smooth bore, and costs little, making it the right pick for PLA, ABS, and PETG. Its weakness is wear — filled filaments grind a brass bore wider in hours. Hardened steel resists that wear and handles carbon fiber, glass fiber, wood-filled, and glow-in-the-dark filament, and it tolerates higher temperatures, but it conducts heat less efficiently than brass, so some printers need a small temperature increase after the swap. Stainless steel sits between the two: tougher and more corrosion resistant than brass, and reasonable when you want one material for standard and mildly abrasive filament. If you print only PLA and PETG, brass is all you need. If you print anything filled, keep hardened steel on hand.

Bore size: start at 0.4 mm, then branch out. The 0.4 mm bore is the standard — it balances detail, speed, and reliability, and most profiles are tuned for it. Smaller bores (0.2 and 0.25 mm) print finer detail and thinner walls for miniatures and small parts, but they print slower and clog more easily. Larger bores (0.6, 0.8, and 1.0 mm) lay down thick lines for fast drafts, large parts, and strong functional pieces, and push filled filament with less trouble. A multi-size kit lets you try each end of the range; a single-size bulk pack makes sense once 0.4 mm is the size you always reach for.

Kits, spares, and cleaning tools. Nozzles are consumables, so a kit beats a single nozzle: a clogged bore at the start of a long print is a five-minute swap when a spare is in the drawer. Check the size mix before you buy — some multi-size kits are heavily weighted toward 0.4 mm, which suits you if that is your standard size and less so if you wanted an even spread. Cleaning needles, a small wrench, and a storage box turn loose nozzles into a kit you can keep organized, and several kits below include them. All five kits here are made for 1.75 mm filament, the standard diameter on the printers they fit.

1. AXEYIL 50-Piece Mixed-Material MK8 Nozzle Kit

The AXEYIL kit is the broadest set here: 45 MK8 nozzles across three materials, plus cleaning tools. Brass covers 0.1 through 1.0 mm, stainless steel covers the most-used sizes, and hardened stainless steel covers abrasive filament — one kit for standard printing, fine detail, fast drafts, and filled filament. The listing counts 50 pieces because the tools are included; the nozzle count itself is 45. If you are stocking a drawer from zero, this kit leaves the fewest gaps.

Specs

  • 45 MK8 nozzles + tools (50 pieces total); brass 30 (0.1, 0.2, 0.3, 0.5, 0.6, 0.8, 1.0 mm ×2 each + 0.4 mm ×16); stainless steel 11 (0.4 mm ×8 + 0.5 mm ×2 + 1.0 mm ×1); hardened stainless steel 4 (0.4 mm ×4); includes curved and straight tweezers, wrench, rigid needles, brushes; MK8 fit for CR-10 and Ender 3; model AQ-553; ASIN B0BWWGMLLC

2. Comgrow 25PCS MK8 Brass Nozzles 0.4mm

The Comgrow kit takes the opposite approach: one size, twenty-five of them. Every nozzle is a 0.4 mm brass MK8 nozzle, the standard bore for everyday PLA and ABS printing on Ender 3 and CR-10 machines — the right buy once you know 0.4 mm is your size and want a deep bench of spares rather than sizes you will never use. The listing states a diameter error under 0.02 mm, and the kit covers the Ender 3 family broadly, including the V2, Max, S1, and Neo, plus the Ender 5 Pro and the CR-10 series.

Specs

  • 25 × 0.4 mm brass MK8 nozzles; 10 cleaning needles, hex wrench, stainless tweezers, storage box; 1.75 mm filament; diameter error under 0.02 mm; item weight 5.3 oz; fits Ender 3, Ender 3 Pro, Ender 3 V2, Ender 3 Max, Ender 3 S1, Ender 3 S1 Pro, Ender 3 Neo, Ender 5 Pro, CR-10 series; ASIN B0B9LYZSKC

3. XIFOWE MK8 Brass Nozzles 24 pcs

The XIFOWE set is a multi-size brass kit weighted toward the size you will use most: sixteen of its twenty-four nozzles are 0.4 mm, with two each of 0.2, 0.6, 0.8, and 1.0 mm for detail work and fast drafts. That mix suits anyone who mostly prints at 0.4 mm but wants the other sizes on hand. The kit includes a ten-grid parts box and a 6 mm hex wrench. It fits MK8 hotends on CR-10 and Ender machines and most 1.75 mm printers with an MK8 block. Note this is the brass kit; XIFOWE sells a separate hardened steel kit under its own listing, and its specifications do not apply here.

Specs

  • 24 brass MK8 nozzles (2 × 0.2 mm + 16 × 0.4 mm + 2 × 0.6 mm + 2 × 0.8 mm + 2 × 1.0 mm); sizes marked on surface; M6 thread, 5 mm thread length; ten-grid parts box + 6 mm hex wrench; fits CR-10, CR-10 mini, CR-10S, Ender 2, Ender 3, Ender 5, MK8 A6 and A8; model NZ-0; ASIN B0969LK4ZT

4. Creality 8 PCS Hardened Steel MK8 Nozzles

The Creality set is the hardened steel pick for MK8 hotends: eight black nozzles in sizes from 0.2 to 1.0 mm, built for abrasive filament that would wear a brass bore out in short order. The listing describes hardened tungsten steel with hardness beyond HRC60 and a maximum temperature of 450 °C, and names PLA and ABS through carbon fiber and even PEEK among the filaments it handles. The eight nozzles span five sizes, and the listing does not state how many of each size are in the pack, so check the listing for the current size breakdown before ordering. The set fits MK8 heating blocks on the Ender 3 series, the CR-10 series, and Makerbot machines. The freshest archived listing is from 2022, so confirm the listing shows stock before ordering. This is the hardened steel eight-piece set, not the separate Creality brass twenty-four-piece kit, a different product.

Specs

  • 8 hardened (tungsten) steel MK8 nozzles; sizes 0.2, 0.4, 0.6, 0.8, 1.0 mm (distribution across the 8 not stated on the listing); hardness beyond HRC60; maximum temperature 450 °C; fits Ender 3, Ender 3 V2, Ender 3 Pro, CR-10 series, Makerbot; model SV-BOZZLES; ASIN B09SG855M9

5. POLISI3D 4pcs Hardened Steel V6 Nozzles

The POLISI3D set is the only V6 pick here, and it is V6 only — do not buy it for an MK8 hotend. The four hardened steel nozzles cover 0.25, 0.4, 0.5, and 0.6 mm, one of each: fine detail, the standard size, and two larger sizes for faster or stronger prints. Each size is marked by dots rather than a printed number: 0.25 mm has no dots, 0.4 mm has three dots, 0.5 mm has six dots, and 0.6 mm has four dots, so check the dots against the listing before fitting one. The set fits V6 hotends on the Prusa i3 MK3S, the Anycubic Mega S, and the Vyper, and is made for 1.75 mm filament including PEI, PEEK, and carbon fiber. The freshest archived listing is from 2022, so confirm stock on the listing before ordering. These are compatible V6 nozzles, not genuine E3D parts.

Specs

  • 4 hardened steel M6 V6 nozzles (1 × 0.25 mm + 1 × 0.4 mm + 1 × 0.5 mm + 1 × 0.6 mm); dot-marked sizes (0.25 = 0 dots, 0.4 = 3 dots, 0.5 = 6 dots, 0.6 = 4 dots); V6 hotend only — not MK8; fits Prusa i3 MK3S, Anycubic Mega S, Vyper; 1.75 mm filament; PEI, PEEK, carbon fiber; ASIN B07J5XCTG7

Comparing the Five Kits

Kit Material Nozzles Sizes Hotend fit
AXEYIL 50-piece Brass, stainless, hardened steel 45 + tools 0.1–1.0 mm MK8
Comgrow 25PCS Brass 25 0.4 mm only MK8
XIFOWE 24 pcs Brass 24 0.2–1.0 mm MK8
Creality 8 PCS Hardened steel 8 0.2–1.0 mm MK8
POLISI3D 4pcs Hardened steel 4 0.25–0.6 mm V6 only

For an Ender 3 or CR-10, the AXEYIL kit is the widest net: three materials, nine bore sizes, and cleaning tools. If 0.4 mm brass is your everyday nozzle, the Comgrow twenty-five-pack is the simplest way to keep spares on hand, and the XIFOWE set is the middle ground — mostly 0.4 mm with the other sizes on hand. For abrasive filament on an MK8 hotend, the Creality hardened steel set is the pick, and for a V6 hotend the POLISI3D four-pack is the only set here that fits.

Frequently Asked Questions

Will an MK8 nozzle fit a V6 hotend?

No. MK8 and V6 nozzles share an M6 thread but differ in length and melt zone, so each seats wrong in the other’s heat block. A wrong-length nozzle can leak filament around the heat break or leave a gap that clogs. Volcano nozzles are longer still and form a third, separate class. Match the nozzle family to your hotend: Ender 3 and CR-10 machines take MK8, Prusa i3 MK3S machines take V6.

What nozzle size should I start with?

Start with 0.4 mm. It is the standard bore on most printers, the size most slicer profiles are tuned for, and a good balance of detail, speed, and clog resistance. Move to 0.2 or 0.25 mm for fine detail or thin walls, and to 0.6, 0.8, or 1.0 mm for fast drafts, large parts, or extra-strong walls. A multi-size kit is the cheapest way to find which sizes you actually use.

When do I need hardened steel instead of brass?

Switch to hardened steel for abrasive filament: carbon fiber, glass fiber, wood-filled, metal-filled, or glow-in-the-dark filament all grind a brass bore wider, which shows up as inconsistent line width and over-extrusion. Hardened steel resists that wear and tolerates higher temperatures for filaments such as PEEK. For plain PLA, ABS, and PETG, brass prints just as well and conducts heat better, so there is no reason to buy steel you do not need.

How often should I replace a nozzle?

Replace a nozzle when print quality falls off: inconsistent extrusion, rough surfaces, new stringing, or clogs that keep coming back after cleaning are all signs the bore has worn or deformed. Brass wears fastest, especially on abrasive filament, while hardened steel lasts far longer on the same material. There is no fixed schedule — it depends on the filament and the hours printed — which is why keeping spares matters more than tracking a replacement date.

Conclusion

A nozzle kit removes a whole class of printing headaches: the right bore for the job, a spare when a clog strikes, and the right material when the filament turns abrasive. The AXEYIL kit covers the most ground for MK8 owners, the Comgrow and XIFOWE brass sets cover everyday 0.4 mm printing at two levels of size spread, the Creality set handles abrasive filament on MK8 hotends, and the POLISI3D set is the V6-only pick for Prusa and compatible machines. Whichever kit you choose, confirm the hotend fit before you order — MK8, V6, and Volcano nozzles are not interchangeable — and keep a spare 0.4 mm nozzle within reach. It is the one you will need first.

Explore Our Guides & Free Tools