- Top Pick: Rode PSA1+ Professional Studio Arm
- Runner-up: Elgato Wave Mic Arm LP
- Also consider: Elgato Wave Mic Arm LP
A microphone boom arm does two jobs at once: it holds the mic exactly where your voice is, and it gets the mic off the desk so keyboard noise and desk vibrations have a harder time reaching the recording. A good arm stays where you put it, swings out of the way when you are done, and keeps the cable tidy.
The five arms below cover the range a PC setup needs, from a budget scissor arm for a first streaming mic to a broadcast parallelogram arm for a heavy XLR mic with a shock mount. Each clamps to a desk and is judged on reach, load range, and mounting.
As an Amazon Associate, we earn from qualifying purchases.
Quick Answer
Pick the Rode PSA1+ for the quietest broadcast-style arm, the Elgato Wave Mic Arm LP when the arm must stay low and out of the camera shot, or the Samson MBA38 for reach across a deep desk. The Elgato Wave Mic Arm suits tall monitors; the InnoGear arm covers a first setup on a tight budget.
Rode PSA1+ Professional Studio Arm
The Rode PSA1+ is the arm most broadcast desks are built around. Its parallel sections move together so the mic stays level as the arm rises and falls, and the damped internal springs keep it from creaking mid-sentence. Reach runs about 37 inches horizontal and 34 inches vertical, clearing wide monitors and deep desks without a riser. The load range covers about 94 grams to 1.2 kilograms, from small USB mics to full-size broadcast dynamics with shock mounts.
One flag: the listing shows an “Is Discontinued By Manufacturer” field, but the value was not visible in the excerpt, so this article states neither way; confirm a live offer on the exact listing. A mic under about 94 grams can drift upward, since the springs need weight to hold the arm down.
Specs
- Model: PSA1+
- Horizontal reach: 37 inches
- Vertical reach: 34 inches
- Load range: 94 grams to 1.2 kilograms
- Item weight: 3.35 pounds
- Product dimensions: 21.25 x 8.25 x 3.25 inches
- Desk mount: clamp and desk insert
- Thread: 3/8 inch with 5/8-inch adapter included
- First available: October 5, 2021
Elgato Wave Mic Arm LP
The Elgato Wave Mic Arm LP solves a different problem: the camera shot. Instead of rising above the monitor, it runs low across the desk, peaking about 6.3 inches above the surface, so the mic sits just below the camera frame and never blocks the screen. It still reaches about 29.1 inches horizontally. Build is all metal, with hidden cable channels, a 2.4-inch clamp, and a 2-kilogram load limit.
The trade-off is height: with no riser, the LP cannot lift a mic over a tall monitor, so it suits setups where the mic approaches from the side. The 2-kilogram limit also needs a check: a heavy mic plus a metal shock mount can get close to it, so weigh the whole assembly, not just the mic body.
Specs
- Model: Wave Mic Arm LP
- Horizontal reach: 29.1 inches
- Maximum load: 2 kilograms
- Item weight: 3.73 pounds
- Product dimensions: 3.46 x 2.36 x 5.51 inches
- Desk clamp: up to 2.4 inches
- Thread: 1/4 inch with 3/8-inch and 5/8-inch adapters included
- Cable management: hidden channels with magnetic covers
- First available: August 17, 2021
Elgato Wave Mic Arm
The standard Elgato Wave Mic Arm is the high-rise version of the LP, built to clear a large monitor. It reaches about 30.7 inches horizontally and 29.5 inches vertically, and a detachable riser adds 5.9 inches, enough to swing the mic over a tall display and down to mouth level. A counterweight keeps it steady, and the ball head and 360-degree base give fine angle control. The mic weight range runs 0.55 to 2.2 pounds with accessories, and the arm itself weighs 4.92 pounds.
It ships with 1/4-inch, 3/8-inch, and 5/8-inch thread adapters, plus a two-year warranty. Two checks before ordering. First, the listing code was confirmed from the product page address and the instruction manual rather than a full Product information excerpt, so confirm the exact listing and a live offer with the API check. Second, the counterweight range has a floor as well as a ceiling: a mic under 0.55 pounds can float upward, so very light USB mics may need the LP.
Specs
- Model: 10AAM9901
- Horizontal reach: 30.7 inches
- Vertical reach: 29.5 inches
- Riser extension: 5.9 inches
- Mic weight range: 0.55 to 2.2 pounds
- Item weight: 4.92 pounds
- Product dimensions: 9.06 x 2.36 x 19.29 inches
- Desk clamp: up to 2.4 inches
- Warranty: 2 years
Samson MBA38 Microphone Boom Arm
The Samson MBA38 is the long-reach pick in this group. It stretches to 38 inches of reach, the longest here, and supports up to 5 pounds, the highest capacity here, covering heavy broadcast dynamics with large shock mounts. The steel body uses internal springs for quiet adjustment, and a C-clamp and a flange mount both come in the box, so the arm can clamp temporarily or screw down permanently.
Two flags. First, the listing code was confirmed from the instruction manual rather than a full Product information excerpt, so confirm the exact listing with the API check. Second, some roundups misstate this arm’s capacity as 5 kilograms; the manufacturer’s own manual states 5 pounds, and this article follows the manual. The 5/8-27 thread means some USB mics need a 3/8-inch adapter, not confirmed as included, so check the mic thread first.
Specs
- Model: MBA38
- Maximum reach: 38 inches
- Maximum load: 5 pounds
- Item weight: 4 pounds
- Product dimensions: 22.44 x 7.09 x 1.57 inches
- Material: steel alloy
- Desk mount: C-clamp and flange mount included
- Thread: 5/8-27
- Springs: internal
InnoGear Microphone Boom Arm
The InnoGear boom arm is the budget pick, and it earns the spot by doing the basics well. The scissor design folds flat when idle and pulls out when needed, with 360-degree base rotation, 135 degrees of extension, a 180-degree arm shaft, and a 270-degree adapter at the mic end. The alloy steel build carries up to 3.3 pounds, handling a Blue Yeti, a HyperX QuadCast, or a Shure MV7 with a shock mount. The box includes a mic clip and a 5/8-inch to 3/8-inch adapter.
The springs sit outside the tubes, so they can ring if the arm is bumped, and cable management is external ties rather than internal channels, which looks messier on camera. The listing code was confirmed from the product page address and listing excerpt rather than a full Product information excerpt, so confirm the exact listing with the API check. Some bundles add a pop filter and a shock mount, so confirm exactly what the listing includes. For a first setup, those are fair trade-offs; for a daily broadcast desk, the Rode or Samson arms hold position more quietly.
Specs
- Brand: InnoGear
- Maximum load: 3.3 pounds
- Item weight: 1.35 pounds
- Product dimensions: 15 x 1.5 x 4 inches
- Material: alloy steel
- Base rotation: 360 degrees
- Desk clamp: up to 2 inches
- Included: mic clip, 5/8-inch to 3/8-inch adapter
How to choose
Start with the load range, not the reach. Weigh the mic, the shock mount, and the cable together, then check that total against both ends of the arm’s range. Counterweight and spring arms, like the Rode PSA1+ and the Elgato Wave Mic Arm, publish a minimum as well as a maximum, and a mic below the minimum drifts upward.
Next, measure the desk. Reach is measured from the clamp, so a 29-inch arm on a 30-inch-deep desk leaves the mic short. Check the clamp opening against the desk thickness, and confirm the edge is flat and squared, since clamps grip poorly on slanted or rounded edges. Thread size comes third: most studio mics use 5/8-inch or 3/8-inch threads and USB mics sometimes use 1/4-inch, so confirm the arm ships with the adapter the mic needs.
Finally, think about the camera shot. A low-profile arm like the Elgato LP stays out of the frame, while a high-rise arm like the standard Elgato or the Rode clears a tall monitor. Internal cable channels look cleaner than external ties, and internal springs run quieter than exposed ones.
Who should skip
Skip a boom arm if the desk is a glass top with a thick edge, has a cable tray under the clamp point, or is thinner than the clamp needs to grip, since a slipping clamp drops the mic. A weighted-base desk stand or floor stand fits those desks better. Skip the heavy broadcast arms if the mic is a featherweight USB model under a quarter pound, since a counterweight arm can lift it out of position; a light scissor arm holds small mics more honestly.
Also skip one when the mic already sits on a good desk stand and never moves. An arm only earns its keep when the mic needs to swing in and out, clear a keyboard, or stay out of the camera frame. If the mic lives in one spot, a stand costs less and cannot sag.
Frequently Asked Questions
What weight can a microphone boom arm hold?
Budget scissor arms usually carry around 3.3 pounds, mid-range arms carry 4.4 to 5 pounds, and broadcast arms like the Rode PSA1+ carry up to about 2.6 pounds but add a minimum load as well. Weigh the mic plus the shock mount and cable together, and check both ends of the range.
Do boom arms fit USB microphones?
Most do, with the right adapter. USB mics often use a 1/4-inch or 3/8-inch thread, while studio arms ship with 5/8-inch threads, so check the adapter in the box. Very light USB mics can also fall below the minimum load of counterweight arms and drift upward.
Low-profile or standard boom arm: which is better for streaming?
A low-profile arm stays below the shoulder line and out of the camera shot, which suits face-cam streaming. A standard arm rises higher and clears tall monitors, which suits setups where the mic comes from above. Pick by the camera angle and monitor height, not by the load rating alone.
Do I need a shock mount with a boom arm?
A shock mount helps whenever the desk carries a keyboard, isolating the mic from taps and bumps that travel through the arm. If the mic is a heavy broadcast model, budget for a shock mount rated for its weight, and add that weight to the arm’s load check.
Final verdict
For most PC gaming and streaming setups, the Rode PSA1+ is the arm to beat: quiet springs, a wide load range, and reach for deep desks. The Elgato Wave Mic Arm LP is the better pick when the camera shot matters, and the Samson MBA38 when the mic must travel furthest or carry the most weight. The standard Elgato Wave Mic Arm covers tall monitors, and the InnoGear arm covers a first setup without overspending. Match the load range first, measure the desk second, and the right arm follows.




