Every PC builder knows the sound: a tiny M.2 screw bouncing off the desk and vanishing into the carpet. Motherboard standoffs, case screws, GPU bracket fasteners, and cooler hardware are all small, steel, and easy to lose at the exact moment you need them again. A magnetic parts tray solves the problem. Drop each fastener into the tray as you remove it, and the magnet holds it in place, even if you bump the bench or tilt the tray to reach a screw.
This guide covers five magnetic trays and bowls for PC building, from a compact mini bowl to a wide rectangular tray for full teardowns. Each pick is chosen for size, material, and holding strength, so you can match the tray to the job.
As an Amazon Associate, we earn from qualifying purchases.
What to Look for in a Magnetic Parts Tray
Start with size and shape. A round bowl suits one fastener group at a time: the screws from a single GPU, a cooler bracket, or an M.2 drive. A rectangular tray gives you a wider landing area for a full teardown, where motherboard, drive, and case screws all come out at once. Sorting by step beats piling everything into one dish: one tray for motherboard hardware, one for drives, one for the case.
Material matters too. Stainless steel resists rust, shrugs off oil and thermal paste, and wipes clean with a cloth. Plastic trays, usually ABS, are lighter and gentler on painted surfaces, which suits a desk you care about or a glossy case. Either works.
Look at the magnet and the base together. The magnet holds steel fasteners inside the tray and sticks the tray to any steel surface, such as a case side panel or a tool cabinet. A rubber-coated base protects the surface underneath from scratches, which matters on a painted case or a finished desk. Trays without base protection can scuff a surface over time, so check for a rubber or coated bottom before you buy.
Think about how you will sort. The simplest system is one tray per stage: a small bowl for the first screws out, a second for the next stage, a large tray for the rest. A set of graduated sizes covers the same ground, since you can dedicate each size to a different fastener group. Masking tape on the rim makes a handy label for each group.
A magnetic parts tray is not a magnetic work mat, a magnetic pickup tool, or a socket organizer. Work mats are flat sheets for laying out tools; pickup tools retrieve dropped fasteners; socket organizers hold sockets in rows. This guide covers trays and bowls only.
One caution applies to every pick here. Keep magnetic trays away from mechanical hard drives, since strong magnets and spinning-disk drives do not mix. Solid-state drives use flash memory and are not affected by these magnets, and the same goes for motherboards, RAM, and graphics cards. Trays on the bench, drives in their bays, and never stack a tray on a hard drive.
1. HORUSDY Magnetic Tray 3-Piece Set
The HORUSDY 3-piece set is the most versatile pick here: three graduated round trays cover every stage of a build in one purchase. The 3-inch bowl holds the tiny screws from an M.2 drive or Wi-Fi card, the 4-inch bowl takes cooler and bracket hardware, and the 6-inch bowl handles case and motherboard screws. Each tray is stainless steel with a rubber-coated magnetic base, so the set sticks to a steel case panel or tool cabinet and stays put on a desk without scratching it.
The graduated sizes are the real advantage over a single tray. Instead of mixing fastener groups in one dish, you can dedicate one bowl to each stage and work through the build in order. The magnets hold the trays vertically or upside down on a metal surface, which helps when bench space is tight. The set weighs 1.06 lb in total.
One note on availability: listings for this set have shown gaps in stock at times, so check the listing before you order.
Specs
- Sizes: 3 in, 4 in, and 6 in round bowls
- Material: Stainless steel with rubber-coated magnetic base
- Pieces: 3 trays
- Model number: 97828
- Weight: 1.06 lb (full set)
- Mounting: Magnetic base sticks to steel surfaces vertically or upside down
- Holding capacity: Not published
2. Grip 6-Inch Stainless Steel Magnetic Parts Tray
The Grip 6-inch tray is the single-tray pick for builders who want one dish for most jobs. It is a stainless steel magnetic tray sized for a full set of case and motherboard screws, with a wipe-clean surface that resists rust and oily workshop conditions. The built-in magnet holds screws, bolts, and sockets in place, and the tray sits beside a motherboard without crowding the bench.
Buy this if you already own a small bowl for tiny fasteners and need a general-purpose dish for everything else. The 6-inch size holds a single-task fastener collection, such as all the screws from a case side panel and drive cage, without taking over the work area. Stainless steel will not rust in a damp garage, wipes clean after contact with thermal paste, and keeps its shape under sockets and brackets.
The listing describes a 6-inch tray; confirm the exact footprint on the listing page before ordering, since third-party descriptions differ on the dimensions. The magnet strength is not rated by the maker, so keep the tray flat when it holds sockets or brackets.
Specs
- Size: 6 in
- Material: Stainless steel
- Pieces: 1 tray
- Magnet: Built-in magnetic base
- Surface: Wipe-clean, rust-resistant steel
- Holding capacity: Not published
3. Titan 11061 Mini Magnetic Parts Tray
The Titan 11061 is the classic mini magnetic bowl, and a go-to pick for PC builders for years. At 4-1/4 inches across, it sits beside a motherboard tray or inside an open case, yet holds every screw from a GPU swap or a cooler installation. The stainless steel bowl has a polished finish and a rubber bottom that keeps it from sliding on the bench or scratching a painted surface.
Small size is the whole point of this pick. A big tray invites you to dump every fastener into one pile; a mini bowl forces a tidier habit, one fastener group at a time. It suits M.2 screws, standoffs, fan screws, and the small brackets that are easiest to lose, and it carries easily from bench to case.
The 11061 is a long-running Titan product, and the tray recommended for PC building by Windows Central. Note that the listing weight field shows an implausibly low figure, a listing data error.
Specs
- Size: 4-1/4 in round
- Material: Stainless steel, polished finish
- Base: Rubber bottom
- Model number: 11061
- UPC: 802090110610
- Manufacturer: Star Asia USA
- Pieces: 1 bowl
- Holding capacity: Not published
4. Titan 21265 Rectangular Magnetic Parts Tray
The Titan 21265 is the wide rectangular option, and the best pick for a full teardown. At 5-3/8 by 9-3/8 inches, it gives you a long landing area where you can lay fasteners out in rows by stage instead of stacking them in a bowl. That habit pays off during reassembly: work the rows in reverse order and every screw goes back where it came from.
Rectangular trays also suit larger hardware: sockets, standoffs, brackets, and cable clips sit flat on the wide base, and the magnetic hold keeps them from sliding when you move the tray. The 21265 is made by Star Asia USA, and it pairs well with a small round bowl: the rectangle for the main teardown, the bowl for the tiny fasteners.
If you buy one tray and regularly strip a system down to the frame, this is the shape to choose. Bowls suit single-component jobs, but a teardown produces too many fastener groups for a 4-inch dish. The rectangle keeps those groups separated and visible at a glance.
Specs
- Size: 5-3/8 x 9-3/8 in rectangular
- Material: Stainless steel
- Model number: 21265
- UPC: 802090212659
- Manufacturer: Star Asia USA
- Pieces: 1 tray
- Holding capacity: Not published
5. OEMTOOLS 25333 Red Magnetic Nut Cup
The OEMTOOLS 25333 is the odd one out here, and that is its strength. Instead of a flat tray or a round bowl, it is a curved ABS plastic cup, 6 inches across, with a coated magnet that sticks to any steel surface. The curved shape lets you position it at any angle: flat on the bench, stuck to the side of a case, or tilted toward you inside an open chassis.
The cup holds up to 5 lb when positioned vertically, the clearest holding figure in this guide. That covers far more than any PC build will ask of it, so load it with sockets and brackets without worrying about the magnet letting go. The ABS body resists oil and fuel, and the rubber coating over the magnets protects work surfaces from scratches. The red color also makes the cup easy to spot on a crowded bench.
Like the HORUSDY set, this listing has shown gaps in stock at times, so check availability before ordering.
Specs
- Size: 6 in diameter curved cup
- Material: ABS plastic with rubber-coated magnets
- Holding capacity: Up to 5 lb in a vertical position
- Mounting: Attaches to steel surfaces at any angle
- Resistance: Oil-resistant and fuel-resistant
- Pieces: 1 cup
Comparing the Five Trays
The five picks split into three shapes, and the shape decides the job. The HORUSDY set gives you three round bowls in graduated sizes, the most flexible single purchase: one bowl per fastener group, from M.2 screws to full case hardware. The Grip 6-inch tray and the Titan 11061 mini bowl are single round dishes at opposite ends of the size range, one for general use and one for small, focused jobs.
The Titan 21265 is the only rectangular tray here, and the pick for full teardowns where fasteners need to be laid out in rows. The OEMTOOLS 25333 is the only cup-shaped pick, and its curved body and 5 lb vertical hold make it the most versatile mounting option, sticking to a case panel at any angle.
Four of the five picks are stainless steel, which resists rust and wipes clean after messy jobs. The OEMTOOLS cup is ABS plastic, lighter and gentler on painted surfaces, and its oil and fuel resistance suits a bench that sees more than PC work.
For a first purchase, the HORUSDY set covers the most ground, since three sizes handle sorting by stage without extra trays. Add the Titan 21265 if you regularly tear a system down to the frame, and keep the Titan 11061 mini bowl beside the motherboard for the smallest fasteners. The Grip tray and the OEMTOOLS cup are strong single-tray options when you already own a bowl and want a different shape.
FAQ
Will a magnetic parts tray damage my PC components?
No, for the components in a modern build. Motherboards, graphics cards, RAM, and solid-state drives are not affected by the magnets in these trays. The one exception is a mechanical hard drive, which uses magnetic storage; keep trays away from spinning-disk drives.
How many magnetic trays do I need for a full PC build?
Two or three trays cover a full build: one for motherboard hardware, one for drive and case screws, and a small bowl for the tiny fasteners from M.2 drives and Wi-Fi cards. A three-piece set like the HORUSDY gives you that system in one purchase.
Is a round bowl or a rectangular tray better for PC building?
It depends on the job. A round bowl suits one fastener group at a time, such as the screws from one GPU or cooler. A rectangular tray suits a full teardown, where you lay fasteners out in rows by stage so reassembly runs in reverse order. Most builders end up owning both shapes.
Can I stick a magnetic tray to my PC case?
Yes, if the case panel is steel. The magnet holds the tray flat, vertically, or at an angle, which frees up bench space. Choose a tray with a rubber-coated base to protect the panel finish, and avoid glass side panels or any panel with a drive mounted directly behind it.
Conclusion
A magnetic parts tray is one of the smallest purchases in a PC building toolkit, and one of the most useful. The HORUSDY 3-piece set covers sorting by stage in one purchase, the Titan 11061 mini bowl handles the smallest fasteners, the Titan 21265 rectangular tray takes full teardowns, the Grip 6-inch tray is a solid general-purpose dish, and the OEMTOOLS 25333 cup mounts at any angle with a 5 lb hold. Pick the shape that matches the work you do most, keep trays away from mechanical hard drives, and lost M.2 screws are a thing of the past.




