Every PC build leaves a trail of small parts: M.2 screws, motherboard standoffs, fan screws, jumper caps, zip ties, and the spare SATA cables that somehow multiply in a drawer. Lose one M.2 screw and a drive install stalls. A good parts organizer turns that chaos into a labeled grid where every fastener has a home.
- How to choose a small parts organizer for PC building
- 1. Akro-Mils 10164 64-Drawer Cabinet, Black
- 2. CRAFTSMAN Large Storage Organizer CMST40739, 39-Compartment
- 3. IRIS USA 36-Drawer Small Parts Cabinet, Black
- 4. DEWALT Deep Pro Organizer DWST14825, 10-Compartment
- 5. Stanley SortMaster 014725R, 25-Compartment
- Comparison
- Frequently Asked Questions
- Conclusion
The organizers below fall into two families. Drawer cabinets sit on the bench or hang on the wall and hold dozens of sorted categories at once. Portable compartment boxes carry a working set of parts to the build, to a LAN event, or to a friend’s house. Both beat sandwich bags and open bowls, because compartments keep tiny parts separated and visible. We picked three drawer cabinets and two portable boxes, all with real Amazon listings.
As an Amazon Associate, we earn from qualifying purchases.
How to choose a small parts organizer for PC building
Start with where the organizer will live. A drawer cabinet is bench furniture: it stays put, holds the most categories, and rewards builders who keep a permanent workspace. A portable box is a travel case for parts: it goes where the build goes, and its lid locks every compartment shut so screws stay sorted in transit. Many builders end up with both, but if you buy only one, match it to your most common build location.
Drawer count and drawer size matter more than total volume. PC hardware is small, so dozens of shallow drawers beat a few deep ones. M.2 screws, washers, and jumper caps need tiny compartments; fan screws and standoffs need medium ones; cable ties and SATA cables need a few large bins.
Look at how the drawers behave. Removable drawers let you carry one category to the case and back. Dividers inside a drawer split one compartment into two or three, which helps when two screw sizes look alike. A rear stop tab or a lip keeps a drawer from sliding all the way out, and clear drawer fronts let you see what is inside without opening anything. Wall mounting frees bench space, and stacking lets a second cabinet grow upward instead of outward.
For portable boxes, the lid is the whole point. A lid that locks every compartment in place stops screws from migrating between sections when the box tips over in a bag. Removable cups beat fixed dividers because you can reconfigure the layout for each project. Metal latches outlast plastic ones, and a water-resistant seal keeps dust and spills away from the contents.
1. Akro-Mils 10164 64-Drawer Cabinet, Black
The Akro-Mils 10164 is the classic bench cabinet. Sixty-four equal-size drawers give you a dedicated home for every screw size, washer, jumper, and connector in a PC builder’s inventory, and the cabinet’s footprint is small enough to sit on a bench shelf or hang on the wall above it. The drawers are clarified polypropylene, so you can see the contents at a glance, and each drawer is removable, so you can carry one drawer of M.2 screws to the case.
The frame is high-impact polystyrene, and the cabinet is made in the USA. It stacks securely with a second unit, and keyhole slots on the back let it wall-mount. Dividers come molded into the cabinet back — eight small and four large — so you can split drawers that hold two similar screw sizes, and rear stop tabs keep a drawer from sliding out and spilling.
The one real limitation is drawer size: every drawer is the same small size, so the cabinet is ideal for screws and jumpers but too small for cable bundles or spare fans.
Specs
- Drawers: 64 equal-size removable drawers, clarified polypropylene
- Overall size: 20 x 6-3/8 x 15-13/16 in
- Drawer inside: 5-1/4 x 1-11/16 x 1-1/2 in
- Frame: High-impact polystyrene, made in USA
- Dividers: 8 small + 4 large included
- Mounting: Stackable, wall-mountable (keyhole slots)
- Weight: About 7 lb
2. CRAFTSMAN Large Storage Organizer CMST40739, 39-Compartment
The CRAFTSMAN CMST40739 takes a different approach: instead of 64 identical drawers, it gives you 39 drawers in two sizes — nine large and 30 small — so one cabinet covers both tiny fasteners and bulkier parts. The large drawers, roughly 5.25 x 4.25 x 2.1 in, hold fan screws, standoffs, cable ties, and small tools. The small drawers, roughly 5.5 x 2 x 1.4 in, are the right size for M.2 screws, washers, and jumper caps. Transparent drawer fronts keep every category visible, and the bin system stacks or wall-mounts.
The near-square front face, about 14.2 in wide and 14.2 in tall, fits on a bench shelf or a wall section that a wider cabinet would crowd. The whole unit is plastic, frame and drawers alike, and four mounting holes on the back secure it to a wall. Assembly takes about 15 to 30 minutes; the drawer slots accept dividers, which are not included.
Specs
- Drawers: 39 total (9 large + 30 small), transparent fronts
- Large drawer: About 5.25 x 4.25 x 2.1 in
- Small drawer: About 5.5 x 2 x 1.4 in
- Overall size: About 14.2 x 6.2 x 14.2 in
- Material: Plastic frame and drawers
- Mounting: Benchtop, stackable, or wall-mount (4 mounting holes)
- Assembly: Required, about 15 to 30 minutes
3. IRIS USA 36-Drawer Small Parts Cabinet, Black
The IRIS USA 36-drawer cabinet splits the difference between the Akro-Mils and the CRAFTSMAN: 32 small drawers for fasteners plus four extra-large bin drawers with dividers for bulkier items. The small drawers measure 6 x 1.75 x 1.5 in inside, which fits M.2 screws, standoffs, and jumper caps, while the XL bins at 6 x 8.1 x 3.2 in swallow cable ties, SATA cables, and spare fans.
The cabinet is made in the USA from plastic, weighs 5.16 lb, and needs no assembly. Interlocking feet let units stack securely, and four mounting holes on the back allow wall hanging. A built-in lip at the back of each drawer keeps the contents from falling out, and the clear drawers show what is inside without opening anything.
At 19.5 in wide, 7 in deep, and 15.5 in tall, it is the widest cabinet in this lineup, so measure your bench shelf before buying. The width is what buys the four XL bins, though, and for builders who want one cabinet that handles both screws and cables, that trade is worth it. The Black 36-drawer unit is part number 580089.
Specs
- Drawers: 36 total (32 small + 4 extra-large bin drawers with dividers)
- Small drawer inside: 6 x 1.75 x 1.5 in
- XL drawer inside: 6 x 8.1 x 3.2 in
- Overall size: 19.5 x 7 x 15.5 in
- Weight: 5.16 lb
- Material: Plastic, made in USA
- Assembly: None required
- Mounting: Stackable (interlocking feet), wall-mountable (4 mounting holes)
4. DEWALT Deep Pro Organizer DWST14825, 10-Compartment
The DEWALT Deep Pro Organizer is the portable pick for builders who carry parts to the job. Ten removable cups sit inside a rugged plastic box with a clear, impact-resistant lid, and the lid locks every compartment in place so screws stay sorted when the box tips in a bag or a truck. The cups lift out and rearrange, so you can build a layout for each project: narrow cups for M.2 screws and standoffs, wide cups for cable ties and fan screws.
The build quality is what sets it apart from generic compartment boxes. Metal latches with an anti-rust treatment close with a positive snap, metal hinges hold the lid, and an IP53 water seal keeps dust and splashes out. A built-in wide handle makes one-hand carry easy, and the units stack with other DEWALT Pro organizers. The DEWALT spec sheet rates the load capacity at 17.6 lb, more than enough for a full working set of fasteners.
The 10-compartment Deep Pro is the model to get; DEWALT also sells a shallower 10-compartment version and a 20-compartment version under different model numbers, so check that the listing shows DWST14825.
Specs
- Compartments: 10 removable cups, reconfigurable layout
- Overall size: 17.5 x 14 x 4.5 in
- Load capacity: 17.6 lb (DEWALT spec sheet)
- Weight: 4.3 lb (DEWALT spec sheet)
- Lid: Clear, impact-resistant, locks all compartments in place
- Latches: Anti-rust metal; metal hinges
- Seal: IP53 water seal, water resistant
- Handle: Built-in wide handle; stacks with other DEWALT Pro organizers
5. Stanley SortMaster 014725R, 25-Compartment
The Stanley SortMaster 014725R is the workhorse compartment box: 25 multi-sized removable cups in three sizes under a clear ABS lid that locks every compartment in place. The three cup sizes let you sort by part type in one box — small cups for M.2 screws and jumpers, medium cups for fan screws and standoffs, large cups for cable ties and connectors — and the removable dividers allow up to 1024 different configurations.
The box is light at 12.32 oz, with a built-in wide handle for easy carrying and angled corners that fit longer items such as a small screwdriver. The clear lid shows the contents without opening, and the lid’s ribbed structure interlocks with the dividers to keep small parts from rolling between compartments. The maximum weight recommendation is 10 lb, which suits fasteners and small parts rather than heavy tools.
Two honest notes: the SortMaster is not water resistant, so keep it out of wet garages and away from drinks on the bench. And availability on Amazon has been intermittent — the listing is carried by marketplace sellers rather than Amazon directly, so confirm the listing before ordering. The SortMaster Junior (14 compartments) and the multi-level cantilever version (23) are different models.
Specs
- Compartments: 25 multi-sized removable cups in 3 sizes
- Overall size: About 17 x 13 x 3.5 in
- Weight: 12.32 oz
- Max weight recommendation: 10 lb
- Lid: Clear ABS, locks all compartments in place
- Material: Plastic, Black and Yellow
- Water resistance: Not water resistant
- Stacking: Side latches lock units together; up to 1024 configurations
Comparison
The three drawer cabinets cover the bench, and the two portable boxes cover the road. The Akro-Mils 10164 has the most drawers at 64, all the same small size, which makes it the best pure fastener library. The CRAFTSMAN CMST40739 mixes nine large drawers with 30 small ones in a compact near-square cabinet, and the IRIS USA adds four extra-large bins to 32 small drawers in the widest cabinet of the three. If you also store cables, ties, and small tools, the CRAFTSMAN or the IRIS covers more categories in one unit.
For portable storage, the DEWALT Deep Pro is the tougher box: metal latches, metal hinges, a water-resistant seal, and a 17.6 lb load rating. The Stanley SortMaster is lighter and has more compartments at 25, with three cup sizes and a far more flexible divider system. A practical setup is one drawer cabinet on the bench plus one portable box for the working set.
Frequently Asked Questions
How many drawers do I need for PC building parts?
For a single build, 10 to 25 compartments cover the parts list: motherboard screws, M.2 screws, standoffs, fan screws, cable ties, and jumpers. For a permanent bench inventory that also holds spare cables and connectors, a 36-drawer or 64-drawer cabinet gives every category its own home.
Are drawer cabinets better than compartment boxes for small parts?
Drawer cabinets hold more categories and stay organized on the bench, but they do not travel. Compartment boxes carry a working set to the build and lock shut for transport. Most builders who build often end up with one of each: a cabinet for storage and a box for the parts in active use.
Can I wall-mount a small parts cabinet?
Yes, all three drawer cabinets in this guide wall-mount. The Akro-Mils uses keyhole slots, while the CRAFTSMAN and IRIS cabinets have mounting holes on the back. Use screws driven into studs or proper wall anchors, and keep the heaviest drawers low.
How do I keep tiny screws from mixing between compartments?
Use a box whose lid locks every compartment in place, like the DEWALT or the Stanley picks above, and keep the lid closed whenever the box moves. In a drawer cabinet, use the included dividers to split drawers that hold similar screw sizes, and label each drawer front so parts go back to the right home after every build.
Conclusion
A small parts organizer is one of the cheapest upgrades a PC builder can make, and it pays for itself the first time a build does not stall on a missing M.2 screw. The Akro-Mils 10164 is the best fastener library, the CRAFTSMAN and IRIS cabinets cover mixed parts in one unit, and the DEWALT and Stanley boxes carry a sorted working set anywhere. Pick the style that matches where you build and label every drawer.




